Windshield & stand for spirit stove - ideas?

Discussion about making bushwalking-related equipment.

Windshield & stand for spirit stove - ideas?

Postby ggorgeman » Fri 25 Jun, 2021 10:06 am

Hi All,
I'm keen to go a bit lighter and use a small meths burner instead of gas + gear on shorter trips. Would appreciate some ideas for pot stand and windshield (perhaps integrated), including DIY ideas. I'm likely to use a smaller pot approx 740ml and base diameter 10cm.
Cheers in advance!
ggorgeman
Athrotaxis cupressoides
Athrotaxis cupressoides
 
Posts: 158
Joined: Wed 23 May, 2012 9:50 pm
Region: Victoria
Gender: Male

Re: Windshield & stand for spirit stove - ideas?

Postby Lamont » Fri 25 Jun, 2021 11:07 am

G'day you could start with a small scale DIY (I cut up a wafer tin I had in the cupboard-app 20gms or buy some Titanium app $25 and app 6-8 gms :shock: ) screen for a small outlay on the burner and stand (or better the heavier duty version of the stand) I put up in the UL thread?
User avatar
Lamont
Athrotaxis selaginoides
Athrotaxis selaginoides
 
Posts: 1767
Joined: Sun 21 Feb, 2016 1:27 pm
Location: Upper Kumbukta West
ASSOCIATED ORGANISATIONS: https://www.againstmalaria.com/
Region: Other Country

Re: Windshield & stand for spirit stove - ideas?

Postby ofuros » Tue 29 Jun, 2021 10:18 am

Lots o' ideas out there...off the top of my head.
Pot stand built into the stove... fancy feast/ evernew style, with a separate aluminium or titanium windscreen.

Stove with seperate trivet/ pot stand on top...seperate windscreen again.

Windscreen incorporated pot stand sloping caldera style or vertical. Holds pot in place under pot rim or stretch a heat resistant silicone band around pot at desired height.

All DIY or available online.

Tiergear also sell the x-mesh which is adjustable for different sized alcohol stoves.

There's a rabbit warren of choices out there, enjoy the journey ggorgeman. :wink:

Might be a few pictural ideas here, under 'Liquid'.
https://ofuros.exposure.co/stoves
Mountain views are good for my soul...& getting to them is good for my waistline !
https://ofuros.exposure.co/
User avatar
ofuros
Athrotaxis selaginoides
Athrotaxis selaginoides
 
Posts: 1792
Joined: Fri 05 Feb, 2010 4:42 pm
Region: Queensland
Gender: Male

Re: Windshield & stand for spirit stove - ideas?

Postby crollsurf » Tue 29 Jun, 2021 11:35 am

My setup is light, works well and packs down into 450ml and bigger pots
Stove and stand https://www.ebay.com.au/itm/324185702933
Wind shield which you can cut to size to fit in pot https://www.ebay.com.au/itm/144062317171
I also carry a scourer so I can put the stove on it when the ground is cold. Metho stoves don't like cold ground
User avatar
crollsurf
Athrotaxis selaginoides
Athrotaxis selaginoides
 
Posts: 1631
Joined: Tue 07 Mar, 2017 10:07 am
Location: Sydney
Region: New South Wales
Gender: Male

Re: Windshield & stand for spirit stove - ideas?

Postby Bubbalouie » Tue 29 Jun, 2021 12:50 pm

I made one a few years back, it works a treat.

I bought some titanium foil, cut it to height, folded the two edges so they can clip together to form a ring, it unclipped to go inside the pot. Once I'd done that I used a hole punch to make perforations one the bottom so it could breath.

A bit later I made 4 holes at the top so I could use tent pegs to hold the pot.

Photo attached (sorry about the size, posting from mobile). You can see the modified pegs at the top right, the cross stand I had as backup in case I didn't like the tent peg design.

Shield weighs about 14g, 6g for the modified pegs. I use an Evernew burner (45g I think), nothing else comes close without being much much heavier.

Everything fits in my Toaks 550ml pot with the (also MYOG) stuff sack to hold it all together.

Quick FYI (on the off chance you don't know) some parks only allow gas fires.
Attachments
20191105_181457.jpg
Bubbalouie
Athrotaxis cupressoides
Athrotaxis cupressoides
 
Posts: 420
Joined: Tue 03 Sep, 2013 11:22 pm
Region: South Australia
Gender: Male

Re: Windshield & stand for spirit stove - ideas?

Postby CraigVIC » Tue 29 Jun, 2021 1:18 pm

You can make a pretty light shield for free with a few beer cans and regular scissors
Attachments
inCollage_20210402_200735367_copy_600x480.jpg
inCollage_20210402_200735367_copy_600x480.jpg (75.28 KiB) Viewed 3476 times
CraigVIC
Athrotaxis cupressoides
Athrotaxis cupressoides
 
Posts: 482
Joined: Tue 24 Oct, 2017 6:20 pm
Region: Victoria

Re: Windshield & stand for spirit stove - ideas?

Postby Lamont » Tue 29 Jun, 2021 1:39 pm

Yep. Concur.
Beer can metal is really good. Holds it's shape nicely. Wish I could get 60 cms in one piece for a better wind screen than the one I've got though.
I've still got 6 empty Coopers Ale cans in the cupboard. :D
Pot lid slotted so it fits in my cup. 1gm.
Attachments
20210629_133253.jpg
20210629_133422.jpg
User avatar
Lamont
Athrotaxis selaginoides
Athrotaxis selaginoides
 
Posts: 1767
Joined: Sun 21 Feb, 2016 1:27 pm
Location: Upper Kumbukta West
ASSOCIATED ORGANISATIONS: https://www.againstmalaria.com/
Region: Other Country


Return to Make Your Own Gear

Who is online

Users browsing this forum: No registered users and 3 guests