hole in nylon

Discussion about making bushwalking-related equipment.

hole in nylon

Postby wildwanderer » Sun 30 May, 2021 7:54 am

If I punch a hole in 500D nylon. Just a small hole maybe 50mm in diameter.

Is that hole likely to widen and eventually split open?

Is there anything I can do to mitigate that? (Without a sewing machine)

Thinking out of the box.. if I heat up a metal food skewer and melt a hole would that keep the hole from splitting under load?

The nylon is subject to load. Im thinking of creating a drain hole for a water bottle carrier at the bottom. Will hold about a 1 litre of weight.
User avatar
wildwanderer
Auctorita modica
Auctorita modica
 
Posts: 1530
Joined: Tue 02 May, 2017 8:42 am
Location: In lockdown :(
Region: New South Wales
Gender: Male

Re: hole in nylon

Postby Lophophaps » Sun 30 May, 2021 10:13 am

Holes tend to run if not reinforced. Can you please advise of the colour of the nylon? I have boxes of fabric and can send you a patch. Drain holes are good. The water containers for wine casks I made all have drain holes.
User avatar
Lophophaps
Auctorita modica
Auctorita modica
 
Posts: 3094
Joined: Wed 09 Nov, 2011 9:45 am
Region: Victoria
Gender: Male

Re: hole in nylon

Postby Moondog55 » Sun 30 May, 2021 10:33 am

Hand stitching and a bead of silicon works. For a hole that large I'd use a scrap of flywire mesh cut 10mm bigger and stitched all around. If you don't have any around I could mail you a scrap I'm sure I have some left over somewhere. Or some of the basketball mesh
Ve are too soon old und too late schmart
Moondog55
Lagarostrobos franklinii
Lagarostrobos franklinii
 
Posts: 10268
Joined: Thu 03 Dec, 2009 4:15 pm
Location: Norlane Geelong Victoria Australia
Region: Victoria
Gender: Male

Re: hole in nylon

Postby telemarktim » Sun 30 May, 2021 10:47 am

Hi Wildwanderer, You could patch the hole with nylon with silicone rubber as suggested by Moondog55. Please see my post on this.
https://bushwalk.com/forum/viewtopic.php?f=53&t=35134

Or my website post:

https://timtinker.com/silnylon-glueing/

If the nylon is not the type that bonds well, it will still help to hold things together anyway. It will make it easy to do supplementary hand stitching once the silicone cures. A sewing kit can be obtained from a $2 shop and you can keep it in your bushwalking kit.

An example of the hand stitching is shown below:

Image

Even shirt cotton can be glued and sewn on in this way.

https://timtinker.com/silicone-rubber-for-ultralight-backpacking-gear2/

Hope this helps,
Tim
telemarktim
Atherosperma moschatum
Atherosperma moschatum
 
Posts: 87
Joined: Mon 17 May, 2021 7:17 pm
Region: Victoria
Gender: Male

Re: hole in nylon

Postby Lophophaps » Sun 30 May, 2021 1:59 pm

Another way is to make a square patch with a hole, then sew the patch over the bigger hole in the item. Bias tape can be used to go around the edges of the patch hole, or fold the hole edges in and sew. I did this for my wine cask water container and it's lasted for decades.
User avatar
Lophophaps
Auctorita modica
Auctorita modica
 
Posts: 3094
Joined: Wed 09 Nov, 2011 9:45 am
Region: Victoria
Gender: Male

Re: hole in nylon

Postby wildwanderer » Sun 30 May, 2021 5:58 pm

Thanks all. Great suggestions.
User avatar
wildwanderer
Auctorita modica
Auctorita modica
 
Posts: 1530
Joined: Tue 02 May, 2017 8:42 am
Location: In lockdown :(
Region: New South Wales
Gender: Male


Return to Make Your Own Gear

Who is online

Users browsing this forum: No registered users and 7 guests