Gear problems and causes / solutions

Bushwalking gear and paraphernalia. Electronic gadget topics (inc. GPS, PLB, chargers) belong in the 'Techno Babble' sub-forum.
Forum rules
TIP: The online Bushwalk Inventory System can help bushwalkers with a variety of bushwalk planning tasks, including: Manage which items they take bushwalking so that they do not forget anything they might need, plan meals for their walks, and automatically compile food/fuel shopping lists (lists of consumables) required to make and cook the meals for each walk. It is particularly useful for planning for groups who share food or other items, but is also useful for individual walkers.

Re: Gear problems and causes / solutions

Postby MichelleN » Wed 10 Feb, 2021 8:08 am

Turns out the bottle contained a dud batch. Manufacturer requested it be returned for testing and replacement metho burns perfectly!
MichelleN
Nothofagus cunninghamii
Nothofagus cunninghamii
 
Posts: 3
Joined: Mon 18 Jan, 2021 9:06 am
Region: Victoria
Gender: Female

Re: Gear problems and causes / solutions

Postby Moondog55 » Tue 13 Jul, 2021 4:20 pm

I have a rather big problem with my plastic ski boots
Help and advice needed, even way-out ideas.
The black polyurethane heel pad in my Scarpa T2 boots has started to disintegrate due to hydrolysis.
I need to fabricate 2 replacements.
Before I go and spend any money what are my repair options?
Much wisdom and experience in the forum and I'm hoping for some good ideas
Attachments
IMG_1946.JPG
Offending item
IMG_1946.JPG (141.62 KiB) Viewed 2766 times
IMG_1948.JPG
A big empty hole where black rubber should be
IMG_1948.JPG (101.69 KiB) Viewed 2766 times
Ve are too soon old und too late schmart
Moondog55
Lagarostrobos franklinii
Lagarostrobos franklinii
 
Posts: 10268
Joined: Thu 03 Dec, 2009 4:15 pm
Location: Norlane Geelong Victoria Australia
Region: Victoria
Gender: Male

Re: Gear problems and causes / solutions

Postby GBW » Tue 13 Jul, 2021 9:11 pm

CCF or maybe a stubby holder cut to shape and glued. Depends how hard it needs to be. Rubber floor mat from a car? Glue cardboard together, make a filler using sawdust and glue, carve a piece of wood. Good luck and how's the snow camp going?
"If you wish to make an apple pie from scratch, you must first invent the universe"
User avatar
GBW
Phyllocladus aspleniifolius
Phyllocladus aspleniifolius
 
Posts: 989
Joined: Fri 02 May, 2014 9:03 am
Location: Melbourne
Region: Victoria
Gender: Male

Re: Gear problems and causes / solutions

Postby Moondog55 » Wed 14 Jul, 2021 4:39 pm

I've made a hole mould and cut some old acoustic felt to fit.
Should work well enough when silicon fills in all the small gaps
Ve are too soon old und too late schmart
Moondog55
Lagarostrobos franklinii
Lagarostrobos franklinii
 
Posts: 10268
Joined: Thu 03 Dec, 2009 4:15 pm
Location: Norlane Geelong Victoria Australia
Region: Victoria
Gender: Male

Re: Gear problems and causes / solutions

Postby trailmixisalie » Thu 29 Jul, 2021 1:22 pm

My macpac microlight is about 10 years old and the fabric is starting to sag having the problem no matter how taut I peg the corners out. It's annoying because the inside fly touches the outside material and leaks in. i have tried just tarp (no fly) but when i sit up or move around i scrape it.

is this the final days of it or is there a chance of revival?
trailmixisalie
Nothofagus gunnii
Nothofagus gunnii
 
Posts: 10
Joined: Thu 11 Mar, 2021 10:34 am
ASSOCIATED ORGANISATIONS: n/a
Region: Victoria
Gender: Male

7tm Telemark ski binding DIY repairs

Postby telemarktim » Sun 15 Aug, 2021 4:42 pm

Hi Tasadam and others, I hope my post is in the correct forum?

I have used (and some would say abused) my beloved 7tm Telemark bindings so much that all my skiing on/in them has brought about their demise. My DIY repairs and small modification to make them ready for backcountry/field servicing might interest others. The binding that needed the repair are the 7tm Alpine tour model with the step-in function (on the RHS of the photo). They are so nice to Telemark in that they get all the use (and wear) as I swap the binding over on a quiver of skis that all have the 7tm mounting plate fitted. The poor red ones (on the left) without the power bars get very little use.
Image

Alpine tour pivot bolt
The first repair involved the nut and thread on the main alpine tour pivot bolt. They had been gouged away by repeated contact with the opposing ski edge. "Yes, to all you Telemark experts, I do ski with my feet too close together!"

I have replaced the original bolt. The one shown in the photo below is my replacement from BJ Bearings. It is somewhat harder than the original but is still showing considerable wear. It will be cheap and easy to replace once more when the time comes.
Image

Alpine tour/Telemark lockdown button
The next repair was to the mushroom-headed button that holds down the Alpine tour pivot when Telemarking. It broke while away on tour (luckily on the last day). It would have been very difficult to repair without a comprehensive workshop. The main problem was the removal of the tiny pin that locks the rotary actuator arm to the button. It took considerable time and required a customised drift punching tool. Then came welding and grinding to repair the button. That was just routine.

The photo below shows the repaired button, after removal, welding and grinding back into shape. The repaired portion is slightly shinier than the rest.
Image

So, while I was making the full repair in my workshop at home I also devised a way of removing the difficulty of the pin removal task for future repairs. "I confess, I also lost the the tiny pin, but as far as I was concerned it was NEVERgoing back!"

Underneath the button, I substituted the stubborn actuator holding pin with a split pin, of similar diameter, that could be easily removed at any time to make repairs (as shown in the photo below).
Image

With the use of the split-pin, I even devised a backcountry temporary fix that would allow the telemark tour to continue with the use of a broken button, an old 4mm dia roofing nail and a backpacking multitool (or strong hands). I made the split pin modification to the second binding as a contingency for the future. That binding has earned just as many turns and may fail any time. Here is the nail option that allows the unused portion of a broken button to be used to hold the button in Telemark mode. The head of the nail conveniently locates in a groove to keep the nail in place while skiing (photo below).
Image

For more details please see:
https://timtinker.com/7tm-binding-repairs/

Tim
telemarktim
Atherosperma moschatum
Atherosperma moschatum
 
Posts: 87
Joined: Mon 17 May, 2021 7:17 pm
Region: Victoria
Gender: Male

Re: Gear problems and causes / solutions

Postby telemarktim » Sun 15 Aug, 2021 10:13 pm

Moondog55 wrote:I have a rather big problem with my plastic ski boots
Help and advice needed, even way-out ideas.
The black polyurethane heel pad in my Scarpa T2 boots has started to disintegrate due to hydrolysis.
I need to fabricate 2 replacements.
Before I go and spend any money what are my repair options?
Much wisdom and experience in the forum and I'm hoping for some good ideas



Hey Moondog, How about silicone rubber that is filled or extended with those little glass bubble things that they use in fibreglassing? The composite should be light, even insulating and will last forever or at least longer than the boots. I had a pair of plastic boots where the outer shell hydrolysed and broke in two while skiing. Only found out when I lifted my snow cuffs on my ski pants and the top of the boot fell off. Lucky your damage is cosmetic by comparison. Are you back skiing?
Tim
telemarktim
Atherosperma moschatum
Atherosperma moschatum
 
Posts: 87
Joined: Mon 17 May, 2021 7:17 pm
Region: Victoria
Gender: Male

Previous

Return to Equipment

Who is online

Users browsing this forum: TentPeg and 11 guests